客服中心仓管组负责劳动防护用品的接收、保管。

客服中心仓管组负责劳动防护用品的接收、保管。

Kết quả (Việt) 1:

Đội ngũ quản lý kho của trung tâm dịch vụ khách hàng chịu trách nhiệm tiếp nhận và lưu trữ các sản phẩm bảo hộ lao động.

Kết quả (Việt) 2:

NOTES: UNLESS OTHERWISE SPECIFIED
1. MATERIAL: ADC12 OR EQUIVALENT BY MiTAC APPROVED.
APPEARANCE TREATMENT: SILVER PAINTING.
2 THE PART SHALL BE INDELIBLY IDENTIFIED IN APPROXIMATE AREA
SHOWN USING 2MM TO 4MM HIGH CHARACTERS INCLUDING THE FOLLOWING:
A. MiTAC PART NUMBER
B. MANUFACTURING LOCATION
PARTS DEEMED TOO SMALL FOR MARKING SHALL BE BAGGED AND TAGGED WITH
THE ABOVE INFORMATION.
3. THE MATERIALS AND MANUFACTURING METHODS USED IN THE FABRICATION
OF THIS PART OR ASSEMBLY MUST BE PROVIDED TO MiTAC ME FOR APROVAL.
4. All EDGES NEED TO HAVE COIN TO REMOVE BURR AND SHOULD BE
INSUED SMOOTH FOR TOUCH, MORE THAN 0.1 MM BURR CAN NOT ACCEPTABLE.
SAFE EDGE PER UL1439 ON DESIGNATED EDGES (0.25-0.50MM RADIUS OR
CHAMFER RECOMMENDED). DIE ROLL AND/OR COINING IS ACCEPTABLE.
5. DRAWING FOR INSPECTION PURPOSES ONLY. ACTUAL PART SHALL CONFORM TO ELECTRONIC DATABASE.
6. PARTS ARE TO BE CLEAN AND FREE FROM FOREIGN MATERIAL. DIRT, OIL,
GREASE, MOLD RELEASE OR OTHER CONTAMINANTS ARE NOT ALLOWED.
THERE SHALL BE NO SCRATCHES, WARPS, BURR OR THE LIKE THAT DAMAGE THE APPEARANCE.
7. UNDEFINED BEND ANGLE TOLERANCE: ¡Ó 0.50 DEGREES
8. .STAND OFF, NUT:
M3: A. PUSH FORCE REQUEST, >= 35 KGF.
B. TORQUE REQUEST, >= 10.2 KGF-CM.
M4: A. PUSH FORCE REQUEST, >= 40 KGF.
B. TORQUE REQUEST, >= 20 KGF-CM.
9. THE DISTORTION OF PART SHALL BE LESS THAN 3/1000.
NOT IMPACT TO THE ASSEMBLY OR FUNCTION.
10. DIMENSIONS INDICATED AS *** ARE CRITICAL TO
FUNCTION. THESE DIMENSIONS ARE TO BE USED FOR CAPABILITY
STUDIES TO STATISTICALLY MONITOR ONGOING PROCESS QUALITY
CONTROL AND REQUIRE A MINIMAL PROCESS CONTROL VALUE OF
Cp > 2.0 AND Cpk > 1.5. ANY DEVIATION FROM THESE VALUES
MUST BE DOCUMENTED WITH WRITTEN APPROVAL FROM MiTAC
MECHANICAL ENGINEERING AND RECORDED IN THE QUALITY PLAN.
DIMENSIONS INDICATED AS ** ARE FAI DIMENSION.
11. SUPPLIER SHALL REVIEW ENVIRONMENTAL REQUIREMENTS AND SUBMIT ENVIRONMENTAL
COMPLIANCE DOCUMENTS VIA MiTAC eGP SYSTEM (http://escm.mic.com.tw).
¼t°Ó¥²¶·¨Ï¥ÎMiTAC eGP¨t²ÎÀËμøÀô«O³W®æn
¨(Dh»tPt¤pW:¶/Ç/¬eÛsÃcömÀ.ôm«iOcÃ.Òc©oúm¤.åt¥wó)
12. EXCEPT THE DIMENSION AND TOLERANCE WHICH ARE SPECIFIED IN THIS 2D DRAWING, ALL
THE OTHER FEATURE DIMENSION SHOULD FOLLOW PROVIDED 3D FILE AND GENERAL TOLERANCE
AS SHOWN IN THE DRAWING TOLERANCE TABLE.
13. PLATING INCLUDES ANT- FINGER PRINT. (¹qÁá»Ý¦³¨¾«ü¯¾³B

Kết quả (Việt) 3:

Đội quản lý kho của trung tâm dịch vụ khách hàng chịu trách nhiệm nhận và giữ lại chất nhân tạo.